Elmer Lane 21 - Roundhouse doors

DB excretes the following words: 

Roundhouse doors, what a pain. There are so many of them. Why did nobody tell me this before?!

It seems the wooden doors on the real thing were re-clad with galvanised corrugated iron around 1959-60. Moisture between the wooden framing and wooden cladding had rotted out the covering, and it was felt the corrugations would allow more air to circulate and dry things out. It was noted in that particular paper that the doors were almost always kept open, and that jives with every photo that I have seen of the roundhouse. Maybe they were closed up in big storms.  

In going through my styrene library, I found some cheap(er) JTT sheets that I bought quite a while ago to do the roundhouse... before I forgot I'd bought them. Out they came and became doors, of which I need about thirty.

I started framing these out as I had done for the Railcar Shed, referring to prototype pics of the roundhouse. I thought I had ample .010x.060 styrene strip for the framing, but before I knew it, I'd run out at the halfway mark. Dammit.

And yes, EB, that is the same gunked up styrene glue that you failed to extract anything from. It has since made the store shed, railcar shed, and all those other little offices and sheds.... And its still going strong on the doors! 

The two colour pictures of the depot that I keep looking at (Steam Inclined and 

xxxx

)  both have the doors that faded/pinked shade of red oxide that matches the window casement frames, so I attempted to mix up a batch of that, and my natural impatience had the doors that I had made painted, weathered and installed within about an hour, rather than doing the more sensible option of waiting until the other doors were built and doing them all in one go. 

The 'weathering' consisted of Tamiya panel line detail (a product that I'm falling out of love with) and a cool bottle of AK 'Starship wash' that I picked up while shopping on Paraparaumu's Rodeo Drive with the Head Druff last week. I used this on some of my recent batch of LCs and like it a lot. I have another of their 'interior washes' (for plane models) that I have used on a lot of things, including the roundhouse, but its a bit green-tinted for general use. On the plus side, it has all these little blobs of grit and mess in it that sit wonderfully on models. The starship wash is more a thin sooty wash, but I'm starting to like it. I wish these Mig/Ammo/AK products were more readily available in the provinces. Some flat varnish should have been applied to these doors, but I'd glued them in place before the weathering had completely set.

In other news, with the roundhouse lifted off the depot module and up to my eyes to attach the doors, I finally got around to filling in a few gaps between the casement windows on the outside segment walls with pre-painted reddy-pink styrene strip. 

And touching up a few missing bits of paint. I pre-painted a lot of that stripwood, cut it and glued it together to make the roundhouse, so there were a few imperfect joins that have just received a few blobs of paint. I also painted under the eaves of the raised top-hat roof at the end closest to the public, not that many people will get down that low, and if they do they'll see all sorts of other flaws.

'Soot' was applied above each stall door (weathering powder), and then the whole front of the shed was Dullcoted to keep that all in place.  I was careful not to get any Dullcote on the roof, or any more on the windows. 

The vertical strips were weathered and then the pairs of doors attached to them.

You might also (barely) see the results of using some black 'Vallejo Pigment FX', which is basically finely ground 'pastels/chalk', on the roundhouse tracks and around the donkey boiler room to represent coal dust, oil, grease and other miscellaneous black stuff. I've put that around the main loco in/out/storage tracks as well and reckon it looks ok as a first cut. On the roundhouse tracks I've gone the further step of 'fixing' it in place with Isopropyl alcohol. I suppose we will see tomorrow if it has stuck! * Without fixin's, it will eventually fall off or blow away, as its an incredibly fine powder and doesn't seem to have any adhesive properties, unlike the old Bragdon weathering powders used above the doors.

Presumably the next blog post will be the big reveal as to whether I waited to procure more strip of the matching size to finish the other doors, or just went ahead with the wrong size. Oooo! Cliffhanger ending!  **

* it did!

** spoiler alert, yes I did figure out the obvious alternative....